Wednesday, September 20, 2017
 
www.cyberspacesolutionsinc.com
www.cyberspacesolutionsinc.com Bookmark and Share
Search
 
 
Making and Using a Pad for Shellac
 
Making and Using a Pad for Shellac
Created by Steve on 8/29/2010 7:44:47 PM

When padding shellac the first step is to construct the pad.  In our experience there is no substitute for linen and wool...


Making and Using a Shellac Pad


When padding shellac the first step is to construct the pad (also called a Fad, Rubber, or Tampon).  I make my pads using a 6" to 8" square of linen wrapped around a bit of raw wool about the size of a large chicken egg when lightly compressed in my hand (if you can't find linen medium weight cotton muslin can be used.  Linen has the advantage of strength.)  I prefer raw wool but the remnants of an old athletic sock or sweater will do nicely.  Do not use cotton, cotton batting, or cotton rags. Cotton does not offer the resiliency of wool and will quickly compress into a mat that will not properly meter shellac from the pad to the surface being finished. Cotton lacks the "feed back" and uniform resiliency and absorbency of wool.

Shellac Pad MaterialsMaking Pad, Step 1Shellac Pade, Step 2

Shellac Pad, Step 4Shellac Pad, Step 5

Shellac Pad Ready for Use

With reference to the above photos, moving from left to right and down, begin by with a bit of raw, washed wool that, when lightly compressed in your hand, is about the size of a large chicken egg.

  • You will need a yard or two of medium weight cotton muslin and some washed, raw wool..
  • Begin by putting a bit of wool about the size of a large chicken egg (when lightly compressed in your hand) on the cotton muslin square between the center and one corner..
  • Next, fold the top corner over the wool and then fold the two adjacent corners in over the folded top corner..
  • You will have made a "pocket" with one end open and the wool in the bottom of the pocket, toward the closed end.
  • Make a twist or two in the open end to form a "tail".
  • Then, with the "tail" held in the heel of your hand with your last two fingers...
  • Fold the "head" of the pad forward and hold it between your thumb and two remaining fingers.

Loading the Pad

Always load the pad by opening it and applying shellac and/or alcohol directly to the wool "reservoir". I use small plastic squeeze bottles for this purpose. This technique gives better control over the volume of shellac added to the pad than simply plunging the pad into a container of shellac.  It also allows you to meter the liquid shellac onto the face of the pad more evenly than the "dip" method.  Dipping the pad into shellac saturates the surface causing too much shellac to be discharged at the initial point of contact. This in turn leads to problems in getting a uniform coat of shellac.

When the pad is loaded with shellac, close it and hold it face up.  There should be no liquid visible on the face of the pad (the liquid is all contained in the reservoir). When you gently squeeze the pad between your thumb and forefinger (again, held face up) liquid should "weep" onto the surface of the pad.  

(NOTE: If you have gotten too much shellac in your pad just blot  it on a paper shop towel or rag until you have removed enough material to present the pad as described above.)

With the pad properly loaded you can now apply a drop or two of lubricating oil to the face.  I dip the tip of my finger in a small container of mineral oil and then touch my finger to the face of the pad. The traditional "lubricant" is raw linseed oil but today most prefer mineral oil since it is easier to find.  Also, mineral oil is more easily removed from the finish. The purpose of the oil is to lubricate the pad so that it glides over the drying shellac finish without sticking. The oil does not become part of the finish.

print
rating
  Comments

  
 
 
www.cyberspacesolutionsinc.com
 
 
www.cyberspacesolutionsinc.com www.cyberspacesolutionsinc.com www.cyberspacesolutionsinc.com